Shape | Round |
Usage/Application | Construction |
Material | Stainless Steel |
Grade | 174PH |
Country of Origin | Made in India |
Length | 6 Meter |
17-4 PH Stainless Steel is a martensitic precipitation-hardening stainless steel that provides an outstanding combination of high strength, good corrosion resistance, good mechanical properties at temperatures up to 600 °F (316 °C), good toughness in both base metal and welds, and short-time, low-temperature heat treatments that minimize warpage and scaling.
Length | 6 Meter |
Diameter | 20 MM - 300 MM |
Shape | Round |
Usage/Application | Construction |
Material | Stainless Steel |
Grade | F53/S32750/2507,F55/S32760,F61/S32550/Ferralium 255 |
It is called Duplex because of its mixed microstructure with about equal proportions of ferrite and austenite, Duplex stainless steels are a family of grades, which range in corrosion performance depending on their alloy content. The term “Super-Duplex” was first used in the 1980’s to denote highly alloyed, high-performance Duplex steel with a pitting resistance equivalent of >40 (based on Cr% + 3.3Mo% + 16N%).
With its high level of chromium, Super-Duplex steel provides outstanding resistance to acids, acid chlorides, caustic solutions and other environments in the chemical/petrochemical, pulp and paper industries, often replacing 300 series stainless steel, high nickel superaustenitic steels and nickel-based alloys. The chemical composition based on high contents of chromium, nickel and molybdenum improves intergranular and pitting corrosion resistance. Additions of nitrogen promote structural hardening by interstitial solid solution mechanism, which raises the yield strength and ultimate strength values without impairing toughness. Moreover, the two-phase microstructure guarantees higher resistance to pitting and stress corrosion cracking in comparison with conventional stainless steels. From the introduction of its first-generation, Duplex steel has seen a steady increase in popularity. Recently, the production of highstrength, corrosion resistant super-duplex coil has been implemented in the marine and chemical industries, architecture and mast riggings, wire lines, lifting and pulley equipment and well service strands.
Material Grade | XM-19 |
Shape | Round |
Usage/Application | Construction |
Single Piece Length | 3 meter |
Thickness/Diameter | 2 Inch (Dia) |
Surface Treatment | Hot Rolled |
Material | Stainless Steel |
Country of Origin | Made in India |
Shape | Round |
Material Grade | CuW50-90 |
Material | Copper Alloy |
Technique | Hot Rolled |
Country of Origin | Made in India |
Leangth | 6 Meter |
Single Piece Length | 3 meter |
Usage/Application | Construction |
Finish | Mill Finish |
Material | Nickel Alloy |
Diameter | 3 MM - 200 MM |
Shape | Round |
Country of Origin | Made in India |
Shape | Round |
Usage/Application | Construction |
Size | 10 MM- 100 MM |
Brand | Imported |
Material | Stainless Steel |
Grade | SS303 |
Unit Length | 3 m |
Technique | Hot Rolled |
Single Piece Length | 3 meter |
Brand | Alloyed |
Usage/Application | Construction |
Material | Stainless Steel |
Country of Origin | Made in India |
Shape | Round |
Material Grade | 17-4 PH |
Material | Stainless Steel |
Shape | Round |
Usage/Application | Industrial, Construction |
Single Piece Length | 3 Meter |
Finishing | Mill Finished |
Country of Origin | Made in India |
Shape | Hexagonal |
Usage/Application | Construction |
Size | 85 mm (Dia) |
Brand | Alloyed |
Material | Stainless Steel |
Surface Finish | Unpolished |
Grade | Fe 500 |
Unit Length | 3 m |
Country of Origin | Made in India |
Shape | Square |
Usage/Application | Construction |
Brand | Alloyed |
Material | Stainless Steel |
Surface Finish | Polished |
Grade | Fe 500 |
Unit Length | 3 m |
Country of Origin | Made in India |
Shape | Rectangular |
Usage/Application | Construction |
Size | 20 mm |
Material | Stainless Steel |
Surface Finish | Polished |
Grade | St37-2 |
Unit Length | 3 Meter |
Country of Origin | Made in India |